Power Products

Product Price :Get Latest Price

• Accuracy class 1.0
• Compact DIN case flush panel mounting
• Ultra bright 4+4+4 digit LED display with auto scaling capability
• Field programmable CT/PT Ratio
• True RMS, More than 100 Samples/cycle
• Microcontroller based calculation
• Universal Power Supply
• Auto scrolling feature for easy readability for all parameters even in Single Line display as well.
• LED indicator for each parameter
• RPM[Available in 3 line 3-Phase VAF]
• ON Hour / Run Hour [Available in 3 line 3-Phase VAF]
• Optional Relay output available

Additional Information:

Product Price :Get Latest Price

About Sequential Event Recorder (Model SER 128+):-

The Model SER 128+ is a complete Masibus event recording system for small-scale monitoring applications. Its extensive communication facilities make it especially valuable as front end instrumentation for offloading to higher level hosts via modem devices. At the same time, the Model SER 128+ serves as a local indication and recording source for ongoing events data.

The system is designed in building block fashion for configuring the required capacity with room for future expansion. Its capacity ranges in 64 point increments from a minimum of 64 point increments from a minimum of 64 points (one scanner card) up to a maximum of 128 points for a single cage system.

The Masibus Model SER 128+''s sequential memory is capable of queuing over 220 event message per 64 points on each scanner card. The distribution of memory on separate scanner cards in 64 point increments ensures that the failure of individual cards will not destroy the system''s entire memory bank. In addition, the Model SER 128+ features event storage for analysis purposes in the form of a circular historical buffer, whose design is unique in events recording instrumentation. It stores the last2000 event captured, which can be easily accessed for pre-and post-fault analysis. By using a keyboard entry, a list of all events in the buffer of events occurring since the last request can be requested, which is particularly useful in unmanned applications.

In all, there are six different RS232C ASCII output ports available on the Model SER 128+, with a seventh port configured to accept an IRIG-B clock synchronization input.

Inherent reliability and security ensure the integrity of events data.

A crystal controlled clock that can be synchronized to the AC line, hourly input line, IRIG-B, or satellite receiver. There is battery back-up for both date and time and historical buffer. Finally, a programmable security code is available to limit access to the system.

Features:-

1) Maximum up to 128 point capability in increment of 64 (2 scanner card)

2) 1 millisecond resolution.

3) 10 microseconds scan time.

4) Sequential memory of 220+ event messages per 64 point scanner card.

5) Six RS-232 port

6) IRIG-B for time synchronization.

7)Windows based RCW software for analysis.

Additional Information:

Product Price :Get Latest Price

Masibus MFT has versatile capabilities for electrical parameter monitoring and communication. It measures all sought of electrical parameters including Voltage, Current, PF, Power and Energy. All essential measuring values can be programmed to the output and are available through Modbus / Modnet communication, the connection of the input signals can be freely programmed for 3 phase 3 wire as well as 3 phase 4 wire, for both balanced and unbalanced load.

High sampling rate and true RMS measurement gives accurate reading under all harmonic conditions; measured electrical parameters in MFT can be converted to equivalent current or voltage signals. These signals can be flexibly assigned to four

analog o/p channels. Any parameter can be assigned to any channel as well as single parameter can be assigned to multiple channels. MFT has isolated interface between device’ internal electronics and field to ensure personal safety.

MFT replaces a number of conventional single function transducers and thus reduces the inventory.

It provides 2 digital pulse o/p for Energy and RS485 port supporting Modbus-RTU protocol for communication, and optional RJ45 port supporting Modnet protocol is also available

With a wide range of analog, digital output and communication options MFT can be used in many applications from a simple analog transducer to an Ethernet transducer.

MFT can be further connected to SCADA network, PLC, other indicating instruments and monitoring systems.

• Four Analog Two Digital Outputs [Isolated to each other]
• Up to 30 parameters can be mapped to Analog Output
• Din Rail Mount
• Fully Programmable
• Analog o/p accuracy as per IEC60688
• Accuracy class 0.5s / 0.2s as per IS14697/ IEC 62053-22 for Energy
• PC based Configuration software
• 1-Ph, 3Ph3W, 3Ph4W configurations
• Measures V, I, Hz, PF, KW, KVA, KWh and KVARh
• True RMS measurement
• <350msec Response time
• Sampling frequency better than 3.9 KHz
• Isolated RS485 (Modbus-RTU protocol) / Modnet
• Backlight LCD to display various parameters (optional)

Additional Information:

Product Price :Get Latest Price

Masibus manufactures high quality AC Line Transducers of various types to help you manage and conserve electricity. All electrical parameters such as Current, Voltage, Active Power, Reactive Power, Frequency and Power factor can be accurately measured. A corresponding linearized signal is then transmitted for various applications such as SCADA, S/S automation, remote indication etc. Output proportional to measured electrical parameter can be connected further to Controllers, Data-Loggers, PLC’s, Analog / Digital Indicators, Recorders for display, analysis or control

AC Line transducer series offers an economical and accurate means of current voltage measurement on systems where the waveform is a pure sine wave. Transducers are calibrated to true RMS value of the sine wave. They can also be used with distorted waveforms where high accuracy is not required.

AC line transducers are having its application to interface with RTUs. Masibus make transducers are also available with dual output option. It provides accuracy up to 0.25% FS with up to 2 KV isolation. Hardware calibration is done through trim-pot.

All transducers performs with exceptional accuracy, repeatability and reliability. In addition to being most accurate, our transducers are equally preferred by OEMs/ end users to other makes for their excellent stability over a long period of operation. This world class technology now comes to you at a very competitive price.

AC line transducers are available as current, voltage in 1Ø configuration whereas power, frequency power factor in 1Ø / 3Ø configuration.

• High accuracy class 0.25%
• Confirms to IEC 60688
• AC Line transducers for all requirements
• Excellent long term stability
• Low burden
• Transient protected
• Good isolation impulse resistance
• Minimum ripple at the output
• Fast response
• Full power factor range operation
• ABS DIN rail mounting
• Range Available : V / I / W / VAR / PF / F
• mA/mV/V output available
• Average / True RMS

Product Price :Get Latest Price

Masibus MFT20 is a cost effective with versatile capabilities for electrical parameter monitoring and communication. It measures all sought of electrical parameters including voltage, current, PF, power and energy. All essential measuring values can be programmed to the output and are available through modbus communication, the connection of the input signals can be freely programmed for 3 phase 3 wire as well as 3 phase 4 wire, for both balanced and unbalanced load.

High sampling rate and true RMS measurement gives accurate reading under all harmonic conditions; measured electrical parameters in MFT can be converted to equivalent current or voltage signals. These signals can be flexibly assigned upto two analog o/p channels. Any parameter can be assigned to any channel as well as single parameter can be assigned to multiple channels. MFT has isolated interface between device’ internal electronics and field to ensure personal safety.

Based on field requirement MFT20 offers various accuracy class options like Class 0.2s / Class 0.5s accuracy as per IS14697/ IEC 62053-22. MFT20 replaces a number of conventional single function transducers and thus reduces the inventory.

More than basic metering, it provides THD measurements, Maximum Demand and optionally a Programmable pulse output. Multifunction transducer stores energy and programmed parameters into non-volatile memory.

MFT can be further connected to SCADA network, PLC, other indicating instruments and monitoring systems via RS485 modbus RTU port.

Product Price :Get Latest Price

The PULS PIANO product family has been developed for users who require a simple and reliable power supply. The focus of PIANO power supplies is on the core features: Efficiency, lifetime, reliability and size. Expensive additional functions, such as power reserves, were deliberately omitted. This allows a cost-oriented design without compromising on quality. PIANO power supplies are perfectly suited for a wide variety of applications.

Features

• Reduce costs
  • Great performance at an attractive price
• High efficiency
  • Low power losses lead to a long lifetime and continuously reduced operating cost
• Compact design
  • Its narrow width saves costly space in the system
• Single-board design
  • All components are assembled on one PC-board. The cost savings in the production and testing process are reflected in the prices of the products

Product Price :Get Latest Price

• High accuracy class
• 0.25%
• Confirms to IEC
• 60688
• Power transducers
• for all requirements
• Excellent long term
• stability
• Low burden
• Transient protected
• Both 1-ph & 3-ph
• versions available
• Good isolation &
• impulse resistance
• Minimum ripple at
• the output
• Fast response
• Full power factor
• range operation
• ABS DIN rail
• mounting